How to Do a Garage Door Repair

October 29, 2021 by No Comments

The garage door is the main part of a garage. As a result, it requires regular maintenance to be in excellent condition. There are times when problems with these doors have complications that can leave homeowners in quite a pickle. So if you notice the problem, don’t hesitate to do a garage door repair so you can get the door working again and keep your house safe from intruders.

                Here is how to do a garage door repair:

1) Examine the current issue

          First, determine what’s wrong with the door. Be sure to take note of any pain points such as loud noises or scrapes on either side of the door and inside and out. If there is no obvious visible damage, confirm this by examining each part of the door.

2) Garage Door Repair Steps

          To fix your garage door, empty out any tools you may need for this step. Once that is done, consider having someone help you lift up the doors with their hands on the top to get started.         Take off all of the panels by unscrewing each bolt that holds them in place and then sliding them off. Now check the rollers, which are located at both ends of where the metal tracks are. If they are still intact and not broken or cracked, wipe them down with a dry cloth to remove any dirt or debris so they will work more smoothly once they open again.         If there is damage to either sidetrack brackets, now is the time to replace them. Now you are ready to work on the torsion springs. The torsion spring can be found under each roller, they are metal rods that wind up like a screw but attach to an axle with brackets on either end of it – one left and one right.         Carefully lower both drums that contain these springs by using your hand or using pliers if they won’t budge easily. Once you have enough room between the drums and your garage door opener’s drive shaft (look straight down at the top of the track where there should be two attached bars) give them a firm yank outwards so they come loose of their brackets.

        If these springs do break, replace both of them at the same time to keep the door’s balance even. And if you are not replacing these springs because they still work well, make sure there is enough tension on them by turning the bolts that hold them in place (with your hand or with pliers) until it feels like they are tight enough. Reattach each spring drum back onto the track and reattach all panels securely before testing out your garage door repair.

                Once your issues seem to be resolved you can pull down on the top panel of your garage door to check how it is closing without any problems. If everything seems good, move on to step 3.

                 If there are a lot of new scrapes or the garage door still does not open up all the way, there may be further issues. If so, use a long metal bar to loosen up each torsion spring which will allow you to adjust them again. Be sure to adjust both of them equally so your garage door can remain balanced and closed without having an excess of pressure on anyone side.

                 Lastly, if it is still making noises or seems like something is loose that shouldn’t be (especially if the rollers are now broken) then there might also be additional hardware-related problems that require you to go out and buy new parts in order to fix these issues completely.

                These steps should get rid of most minor issues with your garage door. But if you want to be absolutely sure that everything is working properly, then open up your garage door like normal, drive into it to release the tension on all of the hardware, turn off your opener for a few minutes and then try driving in again. This should give you a sense of whether or not any parts need adjustment before doing a full repair.

                Good luck with your garage door! Hopefully, this article helped you out so you can get your garage back into good working order quickly.

Swift Garage Door Repair LLC provides garage door repair and garage door installation in all of Irving, TX. If you are in need of garage door repair or installation please give them a call at (214) 988-9182. Swift Garage Door Repair LLC is the best garage door repair service in Irvine, Texas. For over three decades they have been providing services to residential and commercial properties in and around the city. They offer a wide range of garage and gate repair services including Rolling Gate Repair, Rolling Gate Installation, Spring Replacement, Garage Door Spring repair and much more. Their contact details are given below:

Address: 613 N O’Connor St Suite# 21B, Irving, TX 75061
Phone Number: (214) 988-9182
Website: https://swiftgaragedoorsrepair.com
Hours of Operation: Monday – Sunday 7am–11:30pm

Leave a Comment

Your email address will not be published. Required fields are marked *